by campbell·Workflow
Illustrative cover generated by AnyPlugins — no product screenshot available.
Demo Mode earns its place in the Blender Extensions library as a former Blender 4.1 bundled add-on, now offered on its own for looping through multiple blend files. It is provided as-is with limited support.
Demo Mode is a Blender add-on that lets you select multiple blend files and loop over them. It was part of the bundled add-ons in Blender 4.1 and is now offered as a standalone extension with limited support. The original author is Campbell Barton, and it is maintained by campbell on the Blender Extensions platform.
Once installed, the add-on lives under File → Demo Menu inside Blender. It requires no special permissions and is compatible with Blender 4.2 LTS and newer. Distribution is under the GNU General Public License v2.0 or later.
With more than 24,000 downloads on Blender Extensions, Demo Mode has found a place among users who need to cycle through several blend files. At around 8.9 KB, it stays small and focused on that single task.
Demo Mode is best for looping through multiple blend files inside Blender.
Demo Mode is completely free to download and use.
Demo Mode is listed as compatible with Blender 4.2 LTS and newer, so it targets recent versions of the software rather than older releases. It began as one of the bundled add-ons in Blender 4.1 and is now distributed as a standalone extension with limited support. If you are on 4.2 LTS or a later build, you should be able to install it and access it from the File menu. For the exact supported versions, check the developer's page on Blender Extensions.
Demo Mode appears under File → Demo Menu once it is installed in Blender. From there you can select multiple blend files and loop over them. The extension can be added by dragging and dropping it into Blender or by installing it from disk through the preferences. Because it began as a bundled add-on in Blender 4.1, its placement follows Blender's standard File menu. See the developer's page for installation and usage documentation.
Demo Mode is released under the GNU General Public License v2.0 or later. The extension requires no special permissions when installed. For the full license terms and any conditions on redistribution or modification, refer to the developer's page on Blender Extensions or the accompanying license text. This catalog lists the add-on as free, though you should confirm current licensing on the developer's page.
Demo Mode requires no special permissions to run in Blender, according to its extension listing. It is a small add-on, around 8.9 KB in size, focused on selecting multiple blend files and looping over them. It started as a bundled add-on in Blender 4.1 and is now offered as a standalone extension with limited support. You can install it by dragging it into Blender or installing from disk. For anything specific to your setup, the developer's page has more detail.
Also in Workflow for Blender.
by k44dev Software
X-Pose Picker is a Blender add-on for riggers and animators that builds selection and control layouts for characters and 3D objects. It works with any rig and runs on Mac, Linux, and Windows.
by emptybraces
My Best Pie Menu Ever is a Blender add-on by emptybraces that opens a pie menu with the W key, consolidating shortcuts for favorite brushes, their parameters, and frequently used functions across multiple modes.
by Sahin Ersoz
Grease Pencil From Mesh is a Blender add-on that converts mesh objects into 3D Grease Pencil objects or Curves, with edge filtering for sharp edges, intersections and curved surface outlines.
by Nidus
SKkeeper is a Blender add-on from Nidus that applies modifiers on a mesh while keeping its shapekeys and drivers intact. It automates collapsing the modifier stack without discarding shapekey data.
by Community
Corrective Shape Keys is a Blender add-on that creates a corrective shape key for the current pose. Previously bundled with Blender 4.1, it's now offered as a standalone extension with limited support.
by Salt Media
BlenderAe2 by Salt Media transfers 3D data and objects between Blender and After Effects in both directions, covering vertices, 3D layer transforms, camera data and layer synchronization.
by MACHIN3
Machin3Tools is a continuously evolving collection of tools and pie menus for Blender, gathered in a single customizable package. It ships in two base variants, Prime and DeusEx, with the DeusEx variant adding more advanced tools.
by MikhailRachinskiy
3D Print Toolbox is a Blender add-on with utilities for 3D printing. It analyzes mesh volume and surface area, checks and fixes geometry, hollows shapes, aligns models to the print bed, and exports to STL, PLY, and OBJ.
by glukoz
UVPackmaster 4 is a UV packing engine for Blender that packs UV maps on the CPU and GPU, using the Cuda and Vulkan APIs, and can run on the CPU and all system GPUs at once.
by MMD
MMD Tools is a Blender add-on for editing MikuMikuDance (MMD) models. It handles importing and exporting model, motion and pose data, along with chopping and joining parts, plus rigid body, material and motion editing.
by HaughtyGrayAlien
SimpleBake brings PBR and traditional texture baking to Blender from a single panel. Select objects, choose maps, and bake — no special node groups or new workflow, working with whatever materials you've already built.
